|
|
For filling and waterproofing of expansion and structural joints, scratches and cracks from 4 up to 20 mm in width in building facilities. Recommended for use on terraces and balconies, swimming pools, bathrooms and kitchens, thermally insulated walls, car park pavements, garage floors, industrial floors and roofs, between ceramic cladding as well as between concrete, steel, timber and PVC components. For bonding of lightweight metal and steel structures. Suitable also for waterproofing, joining and bolting in residential, industrial, road and hydro-engineering construction applications. Being tested for covering power, the hardened surface can be coated with paint and varnish. Intended for interior and exterior use.
| Package |
| Unit |
|
| 600 ml matallic cartridge |
|
Substrate type
Ceramic tiles (glazed, terracotta, gres, mosaic, cotto and clinker tiles) glass tiles and elements, stone tiles and elements, sanitary ceramics, porcelain and faience elements, enamel elements, concrete and cement surfaces, impregnated timber, stainless steel, chromium-plated steel, aluminium and other metals and their alloys. Before using on plastics (polyacrylic, PVC, polyester and epoxide panels, polystyrene) or paint coatings, it is recommended to carry out an adhesion test. Do not use for bonding with polypropylene, polyethylene, Teflon and bitumen.
Substrate preparation
The substrate should be dry and free of adhesives or grouting mortar, dust, dirt, grease, rust, peeling courses or contaminations (e.g. residues of previous sealing materials) that may impair adhesion of the compound. In case of substrates that are porous, brittle, exposed to water or high mechanical loads, prime them with a primer for polyurethane putty. Protect surfaces that are not to be covered with the compound with a painters’ tape. Remove the tape as soon as the compound has been applied.
Instructions for use
Before using the product, pierce the threaded tip of the cartridge and screw the supplied funnel onto the tip. Trim the funnel according to the width of the joint. The cartridge is then to be placed in the application gun. Apply the compound into the crevice with a slight excess. Apply uninterruptedly, leaving no gaps or empty areas. Level the compound with a putty knife or a similar tool, wetted with soapy water, etc. Make sure, this is done within 10 minutes from application
Tools
Hand-operated or pneumatic application gun, putty knife or a similar levelling tool.
Working conditions
Work in ambient temperatures between +5°C and +30°C.
Storage
Store in original, unopened packages in dry place – shelf life 12 months from production date. Store the sealed package in ambient temperatures between +5°C and +25°C. Allowable transport temperature to -15°C.
Notes
The specifications and instructions for use are given for the temperature of (23±2)°C and relative air humidity of (55±5)%. Properties may vary depending on conditions. Use suitable protective clothing and gloves. Keep away from children. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. The manufacturer accepts no responsibility for damage caused by unskilful or inappropriate use of the product.
General recommendations
Work according to building practice, observing health & safety standards and regulations
| Specifications |
| Composition: polyurethane |
| Density |
approx. 1.17 g/ml |
| Presetting time (skinning) |
approx. 10 min |
| Setting time |
approx. 3-4 mm/24 h |
| Elastic recovery |
≥ 60 % |
Mechanical properties at tension – lateral elastic modulus:
- at +23°C
- at -20°C |
> 0,4 MPa
> 0.6 MPa |
| Resistance to flow (for temperatures between +5°C and 50°C) |
≤ 3 mm |
| Volume changes |
≤ 10 % |
| Mechanical properties at fixed elongation |
no damage |
Adhesive/cohesive properties:
- at varied temperatures
- at fixed elongation due to water |
no damage
no damage |
| Thermal resistance upon setting |
between -30 and +80 °C |
Yield per cartridge (310 ml):
- 4-8×6 mm (joint width × joint depth)
- 10-12×7 mm
- 14-16×8 mm
- 17-18×9 mm
- 19-20×10 mm |
between 6 and 13 rm
between 4 and 5 rm
between 2.5 and 3 rm
between 1.8 and 2 rm
between 1.5 and 1.6 rm |
| Colour: grey |
Reference document: PN-EN ISO 11600:2004, type F, class 20HM.
PZH approved.
The Polish Classification of Goods and Services (PKWiU): 20.16.56.0.
Fidor, 2010-05-04. The present product sheet is valid.
|
|
600 ml matallic cartridge |
- |
- |
|
|
|
|
